HV05S04A汽车电子高压整流二极管

Plastic Sealed High Voltage Diode

HV05S04A塑封高压硅堆 PLASTIC SEALED HIGH VOLTAGE DIODE HV05S04A ------------------------------------------------------------------------------------------------------------------------------------ 1.适用范围 / Scope: 本规格书适用于HV05S04A型塑封高压硅堆. The present specifications shall apply to plastic sealed high voltage Diode HV05S04A. 2 .概要 / General: 1.类型/ Type: 硅整流二极管 Silicon Rectification Diode 2.主要用途/ Application: 适用于汽车电子整流。 For working automobile electronics equipment. 3.外观/ Appearance 管体洁净，无任何沾污、锈迹或开裂 The body shall be clean and shall not bear any stain ,rust or flaw. 管体呈黑色。The color of the case will be black. 4. 外形尺寸、标识 / Dimensions and Marking: 5.参考外形 / Reference shape： 批号、制造商标标记※ 负极标记 Lot No,Coporate mark Cathode mark φ2.5 φ0.6 26min 6.5 26min 单位/Dimensions(mm) ※批号、制造商标标记 / Type name,Lot NO. Corporate mark: 制造商标Corporate mark. 年份: 取公历年份的最后一位字符 YEAR: the last character of the calendar year. 月份: 用一位数表示该年份中的月份. MONTH：use one digit express the month of this year. RG × × 批号标记/Lot No mark 月份 Month 标志 Mark 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 0 11 N 12 D 2018-03

1 / 6

HV05S04A 50mA 4.0kV

Plastic Sealed High Voltage Diode

------------------------------------------------------------------------------------------------------------------------------------ 6. 绝对最大数值 / Absolute Maximum Ratings: 序号 No. 1. 2. 项 目 Item 反向重复峰值电压 Repetitive Peak Reverse Voltage 反向不重复峰值电压 Non-Repetitive Peak Reverse Voltage 正向平均电流 Average Forward Current 正向(不重复)浪涌电流 Non-Repetitive Forward Surge Current 反向浪涌电流 Surge Reverse Current 工作环境温度 Ambient Temperature 最高结温 Maximum Junction Temperature 贮存温度 Storage Temperature 符号 Symbol VRRM VRSM o条 件 Conditions (Ta=50C) 50HZ正弦半波平均值 数值 Rating 4.0 5.0 单位 Unit kV kV 3. IF(AV) 50HZ Sine-half Wave Rectification Average Value (Ta=25 oC) 50HZ 10ms正弦半波 50HZ 10ms Sine-half Wave, 三角波WP=1ms (WP=1ms triangular pulse) 50 mA 4. 5. 6. 7. 8. IFSM IRSM TC TJ TSTG 3.0 50 -40 ~ +100 180 -60 ~ +175 A mA °C °C °C 7. 电气特性 / Electrical Characteristics(Ta=25 oC,unless otherwise specified) 序号 No. 1. 2. 3. 4. 8. 物理特性 / Mechanical Characteristics: 重量 / Weight： 约0.24 g 0.24 grams (approx).

2018-03

项 目 Item 正向压降（最高）Forward Voltage Drop max 常温反向漏电流（最高） Normal Temperature Reverse Current Max 高温反向漏电流（最高） High Temperature Reverse Current Max 反向击穿电压（最低） Reverse Breakdown Voltage Min 符号 Symbol VFM IR1 IR2 VZ 条 件 Conditions IFM=10mA VRM=4kV Ta=175oC; VRM=4kV IR=100uA 数值 Rating 5.0 2.0 25 4.5 单位 Unit V uA uA kV 耐震性 / Vibration proof： 5G. 2 / 6

HV05S04A 50mA 4.0kV

Plastic Sealed High Voltage Diode

------------------------------------------------------------------------------------------------------------------------------------ 9. 测试和检验 / Test and Inspection: 除非另有说明，所有的测试在环境温度(5-35)℃,相对湿度(40-85)%的环境中进行。 Unless otherwise specified for the individual test, all tests shall be conducted at an ambient temperature of (5-35)℃ and R.H. (40-85)%. 9.1 引线断裂试验：引线末端加力0.5kg，在距管体6mm固定住并转900，然后朝反向转1800，然后恢复原样，引线不松驰，不折断。 Lead bend test : With a 0.5kg weight attached to the end of the lead ,the same lead shall be clamped 6mm from the rectifier body and clamp turned 90 degrees ,then 180 degrees in the opposite direction ,then returned to the original position .The leads shall sustain this cycle without loosing and breaking. 9.2 正向压降试验：采用图1电路，IF=10mA，正向压降不得超过7.6V。 Forward voltage drop test: Measured in Fig. 1 circuit at IF= 10mA,forward voltage drop (VF)shall not exceed 7.6V. 9.3 反向电流试验：采用图2电路，VR=4KV单向正弦半波50HZ，反向电流不得超过2μA(25℃时)。 Reverse current test : Measured in Fig. 2 circuit at VR =4KV at the half sine wave of 50HZ,reverse current shall not exceed 2μA at 25℃. 9.4 温度变化继之以变湿热试验：整流管必须经过5个周期温度和2个周期交变湿热循环，[-40℃（30分钟）→室温（3分钟）→+130℃（30分钟）→室温（3分钟）] ×5，[25℃↗55℃,相对湿度:98%,（3小时）→55℃,相对湿度:98%↘93%,（10分钟）→55℃,相对湿度：:93%，（8小时40分钟）→55℃,相对湿度:93%↗98%，（10分钟）→55℃↘25℃,,相对湿度:98%,（3小时）→25℃,,相对湿度:98%（9小时）] ×2，整流管须符合9.2-9.3要求。 Temperature Change go on Damp Heat Cyclic Test :The rectifier shall be subjected to 5 temperature cycles and 2 damp heat cyclic cycles , [-40℃(30min)→R.T.(3min)→+130℃(30min)→R.T.(3min)] ×5,[25℃↗55℃,98%R.H,(3h)→55℃,98%R.H↘93%R.H, (10min)→55℃,93%R.H,(8h 40min)→55℃,93%R.H↗98%R.H,(10min)→55℃↘25℃98%R.H,(3h)→25℃, 98%R.H,(9h)] ×2 ,the rectifier shall satisfy item 9.2 to 9.3 9.5 贮存试验:整流管在环境温度为120℃时放置1000小时,室温下稳定1小时,整流管须符合9.2-9.3要求。 Storage test : The rectifier shall be left in an ambient temperature of 120℃ for 1000 hours. Stabilized to room temperature for 1 hour, the rectifier shall satisfy item 9.2 to 9.3. 9.6 耐焊接热试验：将整流器的引线浸入熔融焊料中5秒钟，焊料温度350±10℃,浸至距管体10mm外。 室温中稳定一小时后，整流器应符合9.2-9.3要求。 Soldering heat test : The leads of the rectifier shall be immersed for 5 sec. in molten solder, at a temperature of 350±10℃,to a point 10mm from the body. Stabilized to room temperature for 1 hour, the rectifier shall satisfy item 9.2 to 9.3 . 9.7 易焊性试验：将元件引线浸入温度为235±5℃的熔融焊料槽中,焊料表面应保持清洁，试验后，引线表面的90%以上应覆盖焊料。 Solderability test : The surface of the solder bath shall be kept clean. The component termination shall be immersed into the bath of molten solder at 235±5℃. After the test, more than 90% of the surface must be covered with the solder. 9.8 高温反偏试验: 整流器在环境温度为100℃时，施加VRM=VRRM，f=50HZ正弦半波电压1000小时，。整流器应符合9.2-9.3要求。 High Temperature Reverse Voltage Test: The rectifier shall be threw Half sinewave voltage (VRM=VRRM )with f=50HZ for 1000 hours in an ambient temperature of 100 ℃. The rectifier shall satisfy item 9.2 to 9.3 . 9.9 高压蒸气试验: 整流器在121℃,2×105pa条件下放置10小时后，整流器应符合9.2-9.3要求。 High-pressure smoke Test: The rectifier shall be placed in 121℃,2×105pa for 10 hours, the rectifier shall satisfy item 9.2to 9.3 . 9.10 间隙通电试验: 将整流器施加IF= 30mA,VR=0的正向脉冲电流,通电3分钟,断电3分钟,持续500小时,最后测试应符合9.2-9.3要求。 Discontinuity Electrify Test: The rectifier shall be threw forward pulse current of IF= 30mA,VR=0,turn on 3 min, turn off 3 min,went on 500 hours, the rectifier shall satisfy item 9.2 to 9.3 图1. 正向压降测试电路 / Fig.1 Forward voltage drop test circuit: 2018-03

3 / 6

HV05S04A 50mA 4.0kV

Plastic Sealed High Voltage Diode

------------------------------------------------------------------------------------------------------------------------------------ R mA 直流电源 D V D.C. Source 图2. 反向电流测试电路 / Fig.2 Reverse current test circuit: 电源 D Source R r 示波器 Oscilloscope

10. 使用须知/ Handling instructions: 10.1 这种二极管在空气中不能保证其额定电压和反向特性，故应使用以环氧为主体的树脂进行再次封装，改变外形尺寸以增大爬电距离。 These diodes have been developed to attain size reduction assuming remolding with epoxy-base resin to endure the creeping distance. It is therefore, impossible to guarantee the rated voltage and backward characteristics in the air. 10.2 装配注意点: Special note for assembly a. 高压硅二极管表面必须保持清洁，高压硅二极管与再次封装树脂之间的界面必须保证足够的附着力。 The surface of a high voltage silicon diode must be kept clean. The interface between a high voltage silicon diode and the remolding resin must ensure sufficient adhesion. b. 再次封装的树脂内不允许有气泡，因为气泡会降低绝缘性和可靠性，特别是在高压硅二极管的附近更另不允许有气泡。 No air bubble is allowed in the remolding, resin because it degrades the insulation and reliability. It must not exist especially near the high voltage silicon diode. c.再次封装时使用环氧树脂会使膨胀或收缩的应力最小，从而避免对二极管产生影响。如果采用环氧系以外的树脂，应仔细查其附着力和密封性，以避免水气进入。 The resin material for remolding should be epoxy-base resin and minimum stress from expansion or contraction shall be generated as so to prevent bad influence on the diode .If any resin other than epoxy-base one is used, the adhesion and airtightness to prevent moisture entrance shall be well examined.

2018-03

4 / 6

HV05S04A 50mA 4.0kV

Plastic Sealed High Voltage Diode

------------------------------------------------------------------------------------------------------------------------------------ 11. 内部结构和材料 / Inner Construction and Materials: ⑷ ⑸ ⑵ ⑶ ⑴ NO ⑴ ⑵ ⑶ ⑷ ⑸ 部 件 名 Part name 二极管芯片 Diode chip 连接材料 Contact Materials 表面钝化 Surface Passivation 封装材料 Molding Material 引 线 Lead wire 材料名称和型号 Material and type name N型硅 N-type Silicon 铅锡焊料 Pb-Sn Solder JRC涂布树脂 JRC Coating Resin UL94V-0环氧树脂 Epoxy Resin ( UL 94V-0) 镀锡铜线 Sn Plated Cu wire 备注 Note 台面型 Mesa Type 刚性型 Rigid Type 12. 环保保证 / Environment protect guarantee: 本产品符合《欧州议会和欧盟理事会2003年1月27日关于在电子和电气设备中使用某些有害物质的指令2002/95/EC》。 The product accord with “Directive 2002/95/EC of the European parliament and of the council of 27 january 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment” 13. SGS测试报告 / SGS test report： SGS测试报告有效期壹年 Period of SGS test report is one year. 14. 包装箱上粘贴环保标识格式 / The Carton use format of environment protect label： 40mm边长的正三角形，内部为大写G，标记颜色白底蓝字。 The Carton use format of environment protect label：”G” in the equilateral triangle of 40mm. Label color is blue word and white grounding. G

2018-03

5 / 6

HV05S04A 50mA 4.0kV

Plastic Sealed High Voltage Diode

------------------------------------------------------------------------------------------------------------------------------------ 11. 包装信息 / Packaging information: Tape size: G C A=65.0mm B=52.0mm C=5.0mm G=6.0mm A B Carton packaging: L W H HVGT Box Minimum packing box: Outside packed cartons:

Box size: (mm) L260 x H145 x W80 L415 x H315 x W275 Quantity of packing: (pcs) 5,000 50,000 Gross weight: (kg) 1.18 12.60 2018-03 6 / 6